固浪强力型回填宝

Solid wave strong backfill treasure

产品概述Product Overview：

本产品是一种新型轻质无机材料，轻质保温，使用本产品进行卫生间回填既能减轻建筑物重量，又能规避其他传统回填材料的缺点。此材料直接烧筑，施工简单，成本低廉，能从根本上解决卫浴间渗漏与异味的问题，适用于卫浴间回填。

This product is a new type of light inorganic material, light insulation, using this product can not only reduce the weight of the building, but also avoid the disadvantages of other traditional backfill materials. This material directly burning construction, simple construction, low cost, can fundamentally solve the bathroom leakage and odor problems, suitable for bathroom backfill.

产品特点Product characteristics：

1.流动性:未成型之前具有超强流动性，有效包裹给水和排水管道，延长使用寿命。还能解决卫浴间沉箱防水层施工无法到位的各个死角。

2.轻质性:成品干密度只有水的三分之一左右。

3.阻水性:吸水率较低，表面可以形成荷叶现象。而且一立方上千亿个独立的封闭气泡，使其具有优异的阻水性能，可以一直漂浮在水面上不下沉。

4.环保性:所需原料为水泥、水基泥填充料，本产品为中性，不含苯、甲醛等有害物质，避免了环境污染。

5.施工简单:1-2小时内可全部完工，可以节省大量工时，节约用工成本，申后易维修。

6.整体性︰现场整体浇筑施工，与主体工程紧密结合形成一个整体，中间没有空隙，使其具有优异的阻水性能。

7:耐久性:与我们的建筑一样;主要成份为水泥可以与主体王程同寿

8.抗压性:现场整体浇注，里外如一，不收缩，不下沉，抗压强度达到0.8mp

1. Liquidity: before the formation of a super-strong liquidity, the effective wrapping of water supply and drainage pipes, extend service life. Can also solve bathroom caisson waterproof layer construction can not be in place of each corner.

2. Lightness: the dry density of the finished product is only about one third of that of water.

3. Water Resistance: water absorption rate is low, the surface can form lotus leaf phenomenon. And a cubic of zero separate closed bubbles, so that it has excellent water resistance, can always float on the water surface does not sink.

4. Environmental Protection: the raw materials required for cement, water-based mud filler, this product is neutral, free of benzene, formaldehyde and other harmful substances, to avoid environmental pollution.

5. Construction simple: 1-2 hours can be completed, can save a lot of time, save labor costs, easy maintenance after the application.

6. Integrity The integral casting construction in the field is closely combined with the main project to form a whole, and there is no space in the middle, which makes it have excellent water resistance performance.

7: Durability: the same as our buildings; the main component of cement can be the same age as the main Wang Cheng

8. Compressive Strength: cast on site as a whole, no shrinkage, no subsidence, compressive strength of 0.8 MP

施工工艺Construction Technology：

1、做好初步防水、量好回填高度，最好用搅拌器搅拌，做好准备工作。

2、使用方法:使用固浪回填专用设备，加入40~50kg的水再加入固浪强力型回填宝，调制900~920之间，进行发泡，发泡至简口6~8cm时，加入50kg的水混继续搅拌4~5分钟调节转速至800~820之间直至搅拌均匀。

3、关闭电源,搅拌完成，打开阀门放料至沉箱内。回填至指定高度、回填完成，清理现场，检测回填空间、搅拌增流。自流平、自然干后进行下一道工序。

1, do a good initial waterproof, backfill height, preferably with a mixer mixing, ready to work.

2. Using method: using the special equipment of solid wave backfill, add 40 ~ 50kg water and then add solid wave strong backfill treasure, mix between 900 ~ 920, carry on foaming, when foaming to 6 ~ 8cm, add 50kg of water and continue to stir for 4 ~ 5 minutes to adjust the speed to 800 ~ 820 until mixing well.

3, turn off the power, mixing is completed, open the valve to discharge into the caisson. Backfill to the specified height, backfill completed, clean up the scene, test backfill space, agitation flow. Self-leveling, natural dry after the next process.

使用范围Scope of use：

1.主要用于卫厨间回填，也有其他方面的应用。

2.阳台抬高，空中花园，厕所回填，屋顶隔热层。

1. The utility model is mainly used for backfilling in the bathroom and kitchen, and also has other applications.

2. Balcony elevation, sky garden, toilet backfill, roof insulation.

参考用量Reference dosage： 

干密度300-350公斤每立方、一次成型。视面积大小将回填产品填满所需回填区域即可。

Dry density 300-350 kg per cubic, one molding. Depending on the size of the backfill product to fill the required backfill area can be.

注意事项Points to note：

1.在阴凉干燥处存储，施工环境温度应在5℃以上。

保质期Expiration date：

原装密封产品在干燥阴凉的环境下存放。在正常的储存和运输条件下，产品的保质期为一年。

 

 

The original sealed product is stored in a dry and cool environment. Under normal conditions of storage and transportation, the shelf life of the product is one years.

 

全国免费服务热线：400-843-6198      www.ch-glfs.com



---