固浪聚合物JS防水涂料

Solid wave polymer JS waterproof coating

固浪聚合物JS防水涂料固浪聚合物JS防水涂料是一种以聚丙烯酸酯乳液、乙烯-醋酸乙烯酯共聚乳液菩聚合物乳液与各种添加剂组成的鹤机液料。和水混、石英动、轻重质碳酸钙等无机填料及各种添加剂所组成的羌机粉料通过合理配比、复合制成的。

Gulang polymer JS waterproofing coating gulang polymer JS waterproofing coating is a kind of liquid material composed of polyacrylate emuls

ion, ethylene-vinyl acetate copolymer emulsion and various additives. Mixed with water, quartz, light and heavy calcium carbonate and other inorganic fillers and additives composed of Qiang machine powder by a reasonable ratio, made of composite.

产品特点Product characteristics：

1∶无毒、无害、无污染、易施工，是新一代环保型防水材料。

2:可在潮湿的基面上施工，具有良好环境适应性。

3∶单组份、冷施工、可以用刷、滚、喷、刮等方式进行施工、开盖直涂。

4:具有良好耐候性好、耐老化、延伸性、弹性、粘结性和成模性。

5︰防水层为封闭体系，整体防水效果佳，特别适用于异形结构基层的施工。

1: non-toxic, harmless, non-polluting, easy to construction, is a new generation of environmental protection waterproof materials.

2: can be constructed on the wet base surface, with good environmental adaptability.

3: Single Component, cold construction, you can use brush, roll, spray, scrape and other means of construction, open straight coating.

4: good weather resistance, good aging resistance, extensibility, elasticity, adhesion and molding.

5. The waterproofing layer is a closed system with good overall waterproofing effect, which is especially suitable for the construction of special-shaped structure base course.

使用范围Scope of use：

本产品广泛应用于新旧屋面、内外墙、阳台、水池、隧道、地下通道等防水防潮工程。尤其适用于工业及民用建筑的屋面防水、墙面、槽罐等防水。

This product is widely used in new and old roofing, inside and outside walls, balconies, pools, tunnels, underground passages and other waterproof and moisture-proof projects. Especially suitable for industrial and civil building roofing waterproof, wall, tank and other waterproofing.

施工工艺Construction Technology：

1、先将水泥倒入容器中，再将乳液慢慢加入，同时充分搅拌3-5分钟至形成无生粉团和颗粒的均匀浆料即可使用;(最好使用搅拌器)
2、用毛刷或滚刷直接涂刷在基面上，力度使用均匀，不可漏刷;一般需涂刷2遍(根据使用要求而定)，每次涂刷厚度不超过1mm;前一次略微干固后再进行后一次涂刷(刚好不粘手，一般间隔1-2小时)，前后两次垂直十字交叉涂刷,涂刷总厚度一般为1-2mm;如果涂层已经固化涂刷另一层时先用清水湿润。

3、施工24小时后建议用湿布覆盖涂层或喷雾洒水对涂层进行养护。施工后完全干固前请采取禁止踩踏、雨水、暴晒、尖锐损伤等保护。

4、如有更高防水要求，进行多遍涂刷或添加玻璃网格布，效果更佳。

1. First pour the cement into the container, then slowly add the emulsion, while fully stirring for 3-5 minutes to form a non-raw powder and particles of uniform slurry can be used; (preferably using agitator)

2, with a brush or roller brush directly brush on the base surface, the force to use uniform, not brush; generally need to brush 2 times (according to the use requirements) , each brush thickness not more than 1mm; After the previous slightly dry and then after a brush (just non-stick hand, generally 1-2 hours interval) , before and after two vertical cross brush, brush the total thickness of 1-2 mm; If the coating has been cured when brushing another layer of water first wet.

3. After 24 hours of construction, it is recommended to cover the coating with wet cloth or spray water to maintain the coating. After construction, please take no trampling, rain, sun exposure, sharp injury and other protection before completely dry.

4, if there is a higher waterproof requirements, repeated brushing or add glass mesh cloth, the effect is better.

参考用量Reference dosage： 

防水涂膜厚度1.5mm,用量约为1.5-2.0kg/m(实际用量视基面的实际情况以及需求的防水层厚度而定)。

The thickness of waterproof film is 1.5 mm, the dosage is about 1.5-2.0 kg/m (the actual dosage depends on the actual condition of the base surface and the required waterproof layer thickness) .

注意事项Points to note：

1、施工温度应在5℃至35℃，避免高温和室外阴雨天气使用。

2、粉料和液料拌合后会逐渐硬化故必须3小时内用完，气温高于20℃还要缩短。

3、配料时，应将粉料往液料内缓缓加入，边加粉料边搅拌，充分搅拌成不含颗粒，分散均匀的胶浆为止。静置5-10分钟再施工，切勿另外加水。

4、施主完毕后注意通风，使材料更好的固化成膜。切勿踩踏以免破坏水涂膜，至少48小时后进行闭水试验(视温度而定)

1. Construction temperature should be 5 ° C to 35 ° C, avoid high temperature and outdoor overcast rain weather use.

2. The powder and liquid material will gradually harden after mixing, so it must be used up in 3 hours, and the air temperature above 20 °C will be shortened.

3, batching, should be the powder into the liquid material slowly, while adding powder while stirring, fully stirring into no particles, evenly dispersed until the mortar. Let stand for 5-10 minutes before construction. Do not add water.

4, donors after the attention of ventilation, so that better curing materials into film. Do not step on the film to avoid damaging the water, at least 48 hours after the water test (depending on the temperature)

保质期Expiration date：

原装密封产品在干燥阴凉的环境下存放。在正常的储存和运输条件下，产品的保质期为一年。

The original sealed product is stored in a dry and cool environment. Under normal conditions of storage and transportation, the shelf life of the product is one years.

全国免费服务热线：400-843-6198      www.ch-glfs.com